View BMT333_8534423.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 ? +5v/550ma at operatng bias conditon ? gain = 25.5 db @ 2.65 ghz ? p1db = 33.5 dbm @ 2.65ghz ? lte 10m aclr = 22.7dbm output power at - 50dbc @ 2.65ghz ? intergrated interstage matching ? lead - free/green/rohs - compliant qfn5x5 smt package the BMT333 is a high dynamic range two - stage power amplifer housed in a lead - free/ green/rohs compliant 5x5mm qfn pack- age. the BMT333 uses a high reliabil- ity ingap/gaas hbt process technology. the BMT333 is designed for use where high linearity and gain are required. the BMT333 is able to deliver over 22 dbm output power from 1.8 to 2.7ghz while maintaining supe- rior aclr performance with a few external matching components. all devices are 100% rf/dc screened. product descripton device features 1 device performance _ measured on a berex evaluaton board at 25c, 50 ? 2 oip3 _ measured on two tones with a output power 23dbm/ tone , f2 f1 = 1 mhz.. typical performance 1 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex parameter frequency unit 1.8 2.35 2.55 2.65 ghz gain 29.7 27.4 26.2 25.5 db s11 - 23.4 - 25.8 - 23.1 - 19.3 db s22 - 12.4 - 19.8 - 17.0 - 18.7 db oip3 2 45.1 50 48.3 48.2 dbm p1db 32.9 34.1 33.3 33.5 dbm lte 10m aclr 22.0 23.5 23.0 22.7 dbm wcdma aclr 22.9 24.4 23.9 23.7 dbm noise figure 5.9 5.3 5.0 5.1 db min. typical max. unit bandwidth 1.8 2.7 ghz i bias @ (i ref1&2 + i b1&2 ) 27 ma i c @ ( i c1 + i c2 ) 550 ma v cc /v bias 5.0 v r th 8.7 c/w applicaton circuits rev. a *aclr channel power measured at - 50dbc. - lte set - up: 3gpp lte, fdd e - tm3.1, 10mhz bw, 5mhz ofset, par 9.75 @0.01% prob. - wcdma set - up: 3gpp wcdma, tm1+64dpch, +5mhz ofset, par 9.78 at 0.01% prob. ? base staton/repeaters infrastructure/small cell ? commercial/industrial/military wireless system ? lte / wcdma /cdma wireless infrastructure applicatons absolute maximum ratngs parameter unit ratng operatng case temperature c - 40 to +85 storage temperature c - 55 to +155 juncton temperature c +200 operatng voltage v +6 supply current a 2 input rf power dbm 20 *operaton of this device above any of these parameters may result in permanent damage.
2 v - i characteristcs berex evaluaton board 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a pin confguraton pin no. label 1 i ref1 4,5 rf in 6 v cc1 11,12,13 rf out/v cc2 16 v b2 19 i ref2 20 v b1 2,3,7,8,9,10,14, 15,17,18 gnd backside paddle gnd figure about the reference positon of components
3 typical device data s - parameters (v cc & v bias = +5v, i cq =550ma, t a =25c) 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a freq s11 s11 s21 s21 s12 s12 s22 s22 [ghz] [mag] [ang] [mag] [ang] [mag] [ang] [mag] [ang] 1.8 0.823 48.909 8.999 - 14.544 0.002 - 47.886 0.851 56.153 1.9 0.829 39.208 8.410 - 31.779 0.003 - 54.191 0.851 47.807 2.0 0.829 29.005 7.873 - 48.880 0.002 - 46.186 0.855 39.252 2.1 0.837 19.120 7.499 - 65.053 0.001 - 44.098 0.846 30.329 2.2 0.840 9.645 7.353 - 81.298 0.002 - 103.445 0.846 21.294 2.3 0.839 0.350 7.422 - 101.020 0.004 - 80.766 0.843 12.643 2.4 0.834 - 8.866 7.175 - 122.701 0.003 - 106.587 0.839 3.550 2.5 0.834 - 17.528 6.794 - 143.783 0.003 - 39.239 0.838 - 5.571 2.6 0.834 - 26.175 6.401 - 164.426 0.002 - 150.204 0.833 - 15.217 2.7 0.833 - 34.246 5.948 174.823 0.002 - 71.305 0.832 - 25.071 s - parameter (v cc & v bias = +5v, i cq = 550ma, t a = 25 c, calibrated to device leads)
4 applicaton circuit: 1.8 ghz 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 schematc diagram bom marks c1 1206 10uf tantalum c2 0603 n/a c3 0603 680pf cog/npo c4 0603 1nf c5 0603 1nf c6 0603 n/a c7 0603 0 ? jumper c8 0603 2.5pf c9 0603 n/a c10 0603 4.3pf high q cap c11 0603 3.9pf c12 0603 1uf c13 0603 100pf c14 0603 1nf c15 1206 10uf tantalum l1 0603 2.2nh l2 0603 39nh l3 1008 39nh high q coil r1 0603 150 ? 5% r2 0603 270 ? 5% pcb diagram notce below informaton is subject to change as conditons of the substrate. 1. pin 16 & 20 is used for vce of the inner bias circuit. to eliminate bias line resonance you need above 10mm transmission line and adjust the positon of c2, c3, c4 ,c5 and c6. also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. c10 : we recommend high - q capacitor for beter output power performance. in this document we used 4.3pf(251r14s4r3bv4, eia 0603) of johanson technology. 3.c7 are just jumpers as 0? preliminary datasheet berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a reference object distance input pin l1 1.4mm input pin c8 3.4mm output pin c10 2.6mm pin 16 c3 6.0mm pin 19 c5 1.0mm pin 20 c4 5.0mm
5 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
6 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a 3gpp wcdma tm1 +64dpch 1fa 3gpp lte e - tm3.1 10mhz 3gpp wcdma tm1 +64dpch 4fa 3gpp lte e - tm3.1 20mhz
7 applicaton circuit: 2.35 ghz 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 schematc diagram bom marks c1 1206 10uf tantalum c2 0603 n/a c3 0603 680pf cog/npo c4 0603 1nf c5 0603 1nf c6 0603 27pf cog/npo c7 0603 0 ? jumper c8 0603 1.2pf c9 0603 1.2pf c10 0603 3.3pf high q cap c11 0603 10pf c12 0603 1nf c13 0603 100pf c14 0603 1nf c15 1206 10uf tantalum l1 0603 n/a l2 0603 0 ? jumper l3 1008 18nh high q coil r1 0603 150 ? 5% r2 0603 270 ? 5% pcb diagram notce below informaton is subject to change as conditons of the substrate. 1. pin 16 & 20 is used for vce of the inner bias circuit. to eliminate bias line resonance you need above 10mm transmission line and adjust the positon of c2, c3, c4 ,c5 and c6. also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. c10 : we recommend high - q capacitor for beter output power performance. in this document we used 3.3pf(251r14s3r3bv4, eia 0603) of johanson technology. 3.c7 & l2 are just jumpers as 0? berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a reference object distance input pin c8 4.0mm input pin c9 3.0mm output pin c10 1.2mm pin 16 c3 6.2mm pin 16 c6 5.0mm pin 19 c5 1.0mm pin 20 c4 5.0mm
8 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
9 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a 3gpp wcdma tm1 +64dpch 1fa 3gpp lte e - tm3.1 10mhz 3gpp wcdma tm1 +64dpch 4fa 3gpp lte e - tm3.1 20mhz
10 applicaton circuit: 2.55 ghz 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 schematc diagram bom marks c1 1206 10uf tantalum c2 0603 1nf c3 0603 680pf cog/npo c4 0603 n/a c5 0603 1nf c6 0603 27pf cog/npo c7 0603 0 ? jumper c8 0603 1.0pf c9 0603 1.5pf c10 0603 3.0pf high q cap c11 0603 10pf c12 0603 1nf c13 0603 100pf c14 0603 1nf c15 1206 10uf tantalum l1 0603 n/a l2 0603 0 ? jumper l3 1008 18nh high q coil r1 0603 150 ? 5% r2 0603 270 ? 5% pcb diagram notce below informaton is subject to change as conditons of the substrate. 1. pin 16 & 20 is used for vce of the inner bias circuit. to eliminate bias line resonance you need above 10mm transmission line and adjust the positon of c2, c3, c4 ,c5 and c6. also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. c10 : we recommend high - q capacitor for beter output power performance. in this document we used 3.0pf(251r14s3r0bv4, eia 0603) of johanson technology. 3.c7 & l2 are just jumpers as 0? berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a reference object distance input pin c8 4.1mm input pin c9 2.2mm output pin c10 1.8mm pin 16 c3 3.0mm pin 16 c6 2.0mm pin 19 c5 1.0mm pin 20 c4 5.0mm
11 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
12 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a 3gpp wcdma tm1 +64dpch 1fa 3gpp lte e - tm3.1 10mhz 3gpp wcdma tm1 +64dpch 4fa 3gpp lte e - tm3.1 20mhz
13 applicaton circuit: 2.65 ghz 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 schematc diagram bom marks c1 1206 10uf tantalum c2 0603 n/a c3 0603 680pf cog/npo c4 0603 1nf c5 0603 1nf c6 0603 27pf cog/npo c7 0603 0 ? jumper c8 0603 1.0pf c9 0603 1.2pf c10 0603 3.0pf high q cap c11 0603 10pf c12 0603 1nf c13 0603 100pf c14 0603 1nf c15 1206 10uf tantalum l1 0603 n/a l2 0603 0 ? jumper l3 1008 18nh high q coil r1 0603 150 ? 5% r2 0603 270 ? 5% pcb diagram notce below informaton is subject to change as conditons of the substrate. 1. pin 16 & 20 is used for vce of the inner bias circuit. to eliminate bias line resonance you need above 10mm transmission line and adjust the positon of c2, c3, c4 ,c5 and c6. also you can adjust spectrum regrowth about bandwidth of signals which you want. 2. c10 : we recommend high - q capacitor for beter output power performance. in this document we used 3.0pf(251r14s3r0bv4, eia 0603) of johanson technology. 3.c7 & l2 are just jumpers as 0? berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a reference object distance input pin c8 3.6mm input pin c9 2.8mm output pin c10 0.8mm pin 16 c3 6.2mm pin 16 c6 2.2mm pin 19 c5 1.0mm pin 20 c4 5.0mm
14 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
15 typical performance 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a 3gpp wcdma tm1 +64dpch 1fa 3gpp lte e - tm3.1 10mhz 3gpp wcdma tm1 +64dpch 4fa 3gpp lte e - tm3.1 20mhz
16 typical performance (pout vs icc) 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
17 package outline dimension 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a
18 suggested pcb land patern and pad layout 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a ? notes 1. use 1 oz. copper minimum for top and botom layer metal. 2. a heatsink underneath the area of the pcb for the mounted device is required for proper thermal operaton. 3. ground / thermal vias are critcal for the proper performance of this device. vias should use a 0.5 mm(a) diameter drill and have a fnal plated thru diameter of 0.3 mm(b). package marking yy = year, ww = working week, xx = wafer no.
19 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a lead platng fnish 100% tin mate fnish (all berex products undergoes a 1 hour, 150 degree c, anneal bake to eliminate thin whisker growth concerns.) tape & reel packaging informaton : tape width(mm) : 12 reel size (inches) : 7 device cavity pitch(mm) : 8 devices per reel : 1000 qfn 5x5
20 1.8 - 2.7 ghz 2w high linearity 5v 2 - stage power amplifer BMT333 msl / esd ratng esd ratng: value: test: standard: esd ratng: value: test: standard: msl ratng: standard: class 1c passes 1000v to < 2000 v human body model (hbm) jedec standard jesd22 - a114b class c3 passes >1000v charged device model (cdm) jedec standard jesd22 - c101f level 1 at +260c convecton refow jedec standard j - std - 020 nato cage code: 2 n 9 6 f preliminary datasheet berex website: www.berex.com email: sales@berex.com specifcatons and informaton are subject to change and products may be discontnued without notce. berex is a trademark o f b erex. all other trademarks are the property of their respectve owners. ? 2014 berex rev. a

▲Up To Search▲

Price & Availability of BMT333

	To Download BMT333 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .